Apparently the added constexpr makes gcc's control flow analysis to go deeper.
If from_chars returns with error then the out parameter remains
uninitialized. As it's undefined behavior to use its value, it's better
to just skip the rest of the loop in this case.
Replaces the existing decimal implementation, for substantial
performance improvements with near-halfway cases. This is especially
fast with a large number of digits.
**Big Integer Implementation**
A small subset of big-integer arithmetic has been added, with the
`bigint` struct. It uses a stack-allocated vector with enough bits to
store the float with the large number of significant digits. This is
log2(10^(769 + 342)), to account for the largest possible magnitude
exponent, and number of digits (3600 bits), and then rounded up to 4k bits.
The limb size is determined by the architecture: most 64-bit
architectures have efficient 128-bit multiplication, either by a single
hardware instruction or 2 native multiplications for the high and low
bits. This includes x86_64, mips64, s390x, aarch64, powerpc64, riscv64,
and the only known exception is sparcv8 and sparcv9. Therefore, we
define a limb size of 64-bits on 64-bit architectures except SPARC,
otherwise we fallback to 32-bit limbs.
A simple stackvector is used, which just has operations to add elements,
index, and truncate the vector.
`bigint` is then just a wrapper around this, with methods for
big-integer arithmetic. For our algorithms, we just need multiplication
by a power (x * b^N), multiplication by a bigint or scalar value, and
addition by a bigint or scalar value. Scalar addition and multiplication
uses compiler extensions when possible (__builtin_add_overflow and
__uint128_t), if not, then we implement simple logic shown to optimize
well on MSVC. Big-integer multiplication is done via grade school
multiplication, which is more efficient than any asymptotically faster
algorithms. Multiplication by a power is then done via bitshifts for
powers-of-two, and by iterative multiplications of a large and then
scalar value for powers-of-5.
**compute_float**
Compute float has been slightly modified so if the algorithm cannot
round correctly, it returns a normalized, extended-precision adjusted
mantissa with the power2 shifted by INT16_MIN so the exponent is always
negative. `compute_error` and `compute_error_scaled` have been added.
**Digit Optimiations**
To improve performance for numbers with many digits,
`parse_eight_digits_unrolled` is used for both integers and fractions,
and uses a while loop than two nested if statements. This adds no
noticeable performance cost for common floats, but dramatically improves
performance for numbers with large digits (without these optimizations,
~65% of the total runtime cost is in parse_number_string).
**Parsed Number**
Two fields have been added to `parsed_number_string`, which contains a
slice of the integer and fraction digits. This is extremely cheap, since
the work is already done, and the strings are pre-tokenized during
parsing. This allows us on overflow to re-parse these tokenized strings,
without checking if each character is an integer. Likewise, for the
big-integer algorithms, we can merely re-parse the pre-tokenized
strings.
**Slow Algorithm**
The new algorithm is `digit_comp`, which takes the parsed number string
and the `adjusted_mantissa` from `compute_float`. The significant digits
are parsed into a big integer, and the exponent relative to the
significant digits is calculated. If the exponent is >= 0, we use
`positive_digit_comp`, otherwise, we use `negative_digit_comp`.
`positive_digit_comp` is quite simple: we scale the significant digits
to the exponent, and then we get the high 64-bits for the native float,
determine if any lower bits were truncated, and use that to direct
rounding.
`negative_digit_comp` is a little more complex, but also quite trivial:
we use the parsed significant digits as the real digits, and calculate
the theoretical digits from `b+h`, the halfway point between `b` and
`b+u`, the next-positive float. To get `b`, we round the adjusted
mantissa down, create an extended-precision representation, and
calculate the halfway point. We now have a base-10 exponent for the real
digits, and a base-2 exponent for the theoretical digits. We scale these
two to the same exponent by multiplying the theoretixal digits by
`5**-real_exp`. We then get the base-2 exponent as `theor_exp -
real_exp`, and if this is positive, we multipy the theoretical digits by
it, otherwise, we multiply the real digits by it. Now, both are scaled
to the same magnitude, and we simply compare the digits in the big
integer, and use that to direct rounding.
**Rust-Isms**
A few Rust-isms have been added, since it simplifies logic assertions.
These can be trivially removed or reworked, as needed.
- a `slice` type has been added, which is a pointer and length.
- `FASTFLOAT_ASSERT`, `FASTFLOAT_DEBUG_ASSERT`, and `FASTFLOAT_TRY` have
been added
- `FASTFLOAT_ASSERT` aborts, even in release builds, if the condition
fails.
- `FASTFLOAT_DEBUG_ASSERT` defaults to `assert`, for logic errors.
- `FASTFLOAT_TRY` is like a Rust `Option` type, which propagates
errors.
Specifically, `FASTFLOAT_TRY` is useful in combination with
`FASTFLOAT_ASSERT` to ensure there are no memory corruption errors
possible in the big-integer arithmetic. Although the `bigint` type
ensures we have enough storage for all valid floats, memory issues are
quite a severe class of vulnerabilities, and due to the low performance
cost of checks, we abort if we would have out-of-bounds writes. This can
only occur when we are adding items to the vector, which is a very small
number of steps. Therefore, we abort if our memory safety guarantees
ever fail. lexical has never aborted, so it's unlikely we will ever fail
these guarantees.
This option is off by default, maintaining the previous behavior. When
enabled (along with FASTFLOAT_TEST), it bypasses the FetchContent
machinery for doctest so that a system-wide installation of the doctest
header can be easily used. In this case, the header doctest/doctest.h
should be available on the compiler’s include path.
This option is especially useful for Linux distributions and others that
need to run the tests in fully offline build environments.
Fixes#83.
